Building Insulation – Northern Renaissance
+7 (812) 777 53 99+7 (812) 928 53 998 (800) 707-53-99 Звонок по России бесплатный

URSA P-20

Semi-rigid compressed glasswool plates is designed for the insulation of walls, ventilated facades, soundproof applications etc.

more
thumbnail URSA П-20 - Semi-rigid compressed glasswool plates is designed for the insulation of walls, ventilated facades, soundproof applications etc.

Application:
  • insulation of walls
  • technical insulation
  • soundproof applications
  • Technical parameters

    Thickness
    50-100 мм
    Width
    600 мм
    Length
    1250 мм
    Thermal Conductivity in 10 °C, λ10
    0,034 Вт/м*К
    Thermal Conductivity in 25 °C, λ25
    0,037 Вт/м*К
    Service temperature
    -60...+320 °С
    Reaction to fire
    A1 (non-combustible)

    URSA M-11

    Soft glasswool rolls designed for use in non-loaded horizontal structures.

    more
    thumbnail URSA M-11 - soft glasswool rolls designed for use in non-loaded horizontal structures.

    URSA M-11Ф - glasswool mats coated with aluminum foil.

    Application:
  • Flat roofs
  • partition walls
  • framed external walls
  • Technical insulation of pipelines, air ducts, industrial equipment
  • Technical parameters

    Thickness
    50-100 mm
    Width
    1200 mm
    Length
    depending on thickness
    Thermal Conductivity in 10 °C, λ10
    0,039 W/mK
    Thermal Conductivity in 25 °C, λ25
    0,042 W/mK
    Service temperature
    -60...+320 °С
    Reaction to fire
    A1 (non-combustible)

    URSA M-15

    Tthermal and acoustic insulation for pitched roofs, prefabricated timber walls and other applications.

    more
    thumbnail URSA M-15 - is thermal and acoustic insulation for pitched roofs, prefabricated timber walls and other applications.
    Application:
  • pitched roofs
  • prefabricated timber walls
  • partition walls
  • technical insulation of pipelines, air ducts, industrial equipment
  • Technical parameters

    Thickness
    50-100 mm
    Width
    1200 mm
    Length
    depending on thickness
    Thermal Conductivity in 10 °C, λ10
    0,037 W/mK
    Thermal Conductivity in 25 °C, λ25
    0,040 W/mK
    Service temperature
    -60...+320 °С
    Reaction to fire
    A1 (non-combustible)

    URSA P-30

    Semi-rigid compressed glasswool plates is designed for the insulation of walls, ventilated facades, soundproof applications etc.

    more
    thumbnail URSA P-30 - Semi-rigid compressed glasswool plates is designed for the insulation of walls, ventilated facades, soundproof applications etc.

    Application:
  • ventilated facades
  • soundproof applications
  • insulation of walls
  • Technical parameters

    Thickness
    50-100 mm
    Width
    600 mm
    Length
    1250 mm
    Thermal Conductivity in 10 °C, λ10
    0,033 W/m*K
    Thermal Conductivity in 25 °C, λ25
    0,034 W/m*K
    Service temperature
    -60...+220 °С
    Reaction to fire
    A1 (non-combustible)

    URSA P-15

    Soft, lightweight glass mineral wool slabs are designed for use in pitched roof structures, partitions, frame walls.

    more
    thumbnail URSA P-15 Soft, lightweight glass mineral wool slabs are designed for use in pitched roof structures, partitions, frame walls.

    Technical parameters

    Thickness
    50-100 мм
    Width
    600 мм
    Length
    1250 мм
    Thermal Conductivity in 10 °C, λ10
    0,036 Вт/м*К
    Thermal Conductivity in 25 °C, λ25
    0,039 Вт/м*К
    Service temperature
    -60...+320 °С
    Reaction to fire
    A1
    Sorption humidity for 72 hours,% by weight
    5

    Heat-insulating crushed stone from NEOPORM foam glass

    Granular bulk material from NEOPORM foam glass does not contain combustible components, asbestos and other carcinogenic fibers, does not emit harmful substances, is resistant to ultraviolet radiation and solvents.

    more
    thumbnail Granular bulk material from NEOPORM foam glass does not contain combustible components, asbestos and other carcinogenic fibers, does not emit harmful substances, is resistant to ultraviolet radiation and solvents.

    Application:
    • thermal and acoustic insulation of roofs, walls, foundations, floors, equipment and pipelines;
    • foundation for the road;
    • drainage system insulation;
    • production of light concrete.

    Technical parameters

    Grain size, mm
    5-40
    Volume density, kg/m3
    60-70
    Thermal conductivity at 25°C, W/(m•K)
    0,056
    Compressive strength, MPa
    0,17
    Package size, m3
    1

    Shaped products from NEOPORM foam glass

    Foam glass (cellular glass) – is a rigid heat insulating material with closed-cell structure produced of foamed glass.

    more
    thumbnail Shaped goods are produced by machining the NEOPORM foam glass slabs. The NEOPORM foam glass goods are not toxic, they belong to danger class 4 according to the GOST 12.1.007. When transported, stored and applied the NEOPORM foam glass goods do not produce any damage effect to the environment or man’s health. The shaped goods are produced as follows:

    Pipe shells

    Segments

    Elbows

    Пеностекло НЕОПОРМ® Пеностекло НЕОПОРМ® Пеностекло НЕОПОРМ®

    Size standards of the NEOPORM® foam glass pipe shells and segments

    Пеностекло НЕОПОРМ®: Фасонные изделия  
    Item Value, mm Limit deviation, mm
    Length 600 ± 2
    Width S as agreed with customer ± 2
    Inner diameter dвн sheells from 22 to 219 ± 2
    Inner diameter of dвн segments from 219 ± 2

    Size standards of the NEOPORM® foam glass elbows

    Пеностекло НЕОПОРМ®: Фасонные изделия
    Item Value, mm Limit deviation, mm
    Inner diameter dвн from 57 to 159 ± 2
    Thickness S as agreed with customer ± 2
    Bend radius Rкол as agreed with customer ± 2
      According to specially designed documentation it is possible to produce as follows:
    • right-angled parallelepiped plates with grooves of agreed depth and shape (for heat insulation of complex shaped equipment);
    • conic and ellipsoidal segments;
    • elbows for heat insulation of pipe bends of diameters more than 159 mm.

    Technical parameters

    Density, kg/m3
    121-140 (D130), 141-160 (D150)
    Compression strength, МPа, not less than
    1.0 (D130), 2.0 (D150)
    Heat conductivity at 25 ºС,W/(m·К)
    0,048 (D130), 0,052 (D150)

    Foam glass slabs NEOPORM D150

    Foam glass (cellular glass) – is a rigid heat insulating material with closed-cell structure produced of foamed glass.

    more
    thumbnail Foam glass (cellular glass) – is a rigid heat insulating material with closed-cell structure produced of foamed glass.

    Heat insulating plates are produced by machining the NEOPORM foam glass slabs.

    The NEOPORM foam glass plates are production, mounting and operation safe, they do not contain any ozone destruction substances, they do not emit any harmful and stinking substances during operational period, they are not destructed by rodents or insects, they do not present any growth media for microorganisms, they are stable to impacts of aggressive media.

    Technical parameters

    Density, kg/m3
    141-160
    Compression strength, МPа, not less than
    2.0
    Heat conductivity at 25 ºС,W/(m·К)
    0.052
    Leght, mm
    600
    Width, mm
    450
    Thickness, mm
    40-160
    Limit deviation , mm
    ±2

    Foam glass slabs NEOPORM D130

    Foam glass (cellular glass) – is a rigid heat insulating material with closed-cell structure produced of foamed glass.

    more
    thumbnail Foam glass (cellular glass) – is a rigid heat insulating material with closed-cell structure produced of foamed glass.

    Heat insulating plates are produced by machining the NEOPORM foam glass slabs.

    The NEOPORM foam glass plates are production, mounting and operation safe, they do not contain any ozone destruction substances, they do not emit any harmful and stinking substances during operational period, they are not destructed by rodents or insects, they do not present any growth media for microorganisms, they are stable to impacts of aggressive media.

    Technical parameters

    Density, kg/m3
    121-140
    Compression strength, МPа, not less than
    1.0
    Heat conductivity at 25 ºС,W/(m·К)
    0.048
    Leght, mm
    600
    Width, mm
    450
    Thickness, mm
    40-160
    Limit deviation , mm
    ±2

    PENOPLEX GEO

    Designed for use in industrial and civil construction in loaded structures (eg, foundations, floors, plinths, garden paths, roofs).

    more
    thumbnail PENOPLEX GEO - manufactured by extrusion from General purpose polystyrene. Designed for use in industrial and civil construction in loaded structures (eg, foundations, floors, plinths, garden paths, roofs). Plates of this type are characterized by high strength and are able to withstand significant loads during the entire service life.

    Advantages PENOPLEX:
    • low thermal conductivity;
    • zero water absorption;
    • ecological compatibility;
    • durability;
    • biostability;
    • high compressive and bending strength.

    Aapplication:
    • foundations;
    • floors;
    • Stylobates and parking;
    • roof.

    Technical parameters

    Compressive strength at 10% linear deformation
    0,3 MPa
    Water absorption in 24 hours, not more than % by volume
    0,4
    Water absorption in 28 days % by volume
    0,5
    Fire resistance category
    Г4
    Calculated coefficient of thermal conductivity under operating conditions” B ”
    0,034 W/mK
    Coefficient of vapor permeability
    0,005 mg/(m. h. Pa)
    Density
    28-36 kg/m3
    Modulus of elasticity
    17 MPa
    Specific heat
    1,45 kJ/(kg*°С)
    Tensile strength at static bending
    0,4-07 MPa
    Operating temperature range
    -70...+75 °C
    Thickness
    30-100 mm
    Width
    585 mm
    Lenght
    1185 mm

    PENOPLEX ROOF

    Designed for use in industrial and civil construction, it is a high-strength material for use in any types roof.

    more
    thumbnail PENOPLEX ROOF - Designed for use in industrial and civil construction, it is a high-strength material for use in any types roof.

    Advantages PENOPLEX:
    • low thermal conductivity;
    • zero water absorption;
    • ecological compatibility;
    • durability;
    • biostability;
    • high compressive and bending strength.

    Aapplication:
    • Roofs of any type;
    • Stylobates and parking.

    Technical parameters

    Compressive strength at 10% linear deformation
    0,25 MPa
    Water absorption in 24 hours, not more than % by volume
    0,4
    Water absorption in 28 days % by volume
    0,4
    Fire resistance category
    Г3
    Calculated coefficient of thermal conductivity under operating conditions” B ”
    0,034 W/mK
    Coefficient of vapor permeability
    0,005 mg/(m. h. Pa)
    Density
    26-34 kg/m3
    Modulus of elasticity
    17 MPa
    Specific heat
    1,45 kJ/(kg*°С)
    Tensile strength at static bending
    0,4 MPa
    Operating temperature range
    -70...+75 °C
    Thickness
    20-100 mm
    Width
    585 mm
    Lenght
    1185 mm

    PENOPLEX WALL

    Heat-insulating boards made of extruded polystyrene foam. Used for insulation of external and internal enclosing structures (insulation of walls, partitions, facade systems).

    more
    thumbnail PENOPLEX WALL manufactured by extrusion from General purpose polystyrene. Used for insulation of external and internal enclosing structures (insulation of walls, partitions, facade systems). The plates have a milled surface, which improves the adhesion of plaster and adhesive compounds to the surface of the material and reduces the time of plastering.

    Advantages PENOPLEX:
    • low thermal conductivity;
    • zero water absorption;
    • ecological compatibility;
    • durability;
    • biostability;
    • high compressive and bending strength.

    Aapplication:
    • walls;
    • partitions;
    • facade systems.

    Technical parameters

    Compressive strength at 10% linear deformation
    0,15 MPa
    Water absorption in 24 hours, not more than % by volume
    0,5
    Fire resistance category
    Г4
    Calculated coefficient of thermal conductivity under operating conditions” B ”
    0,034 Вт/м*К
    Coefficient of vapor permeability
    0,005 mg/(m. h. Pa)
    Density
    от 20 kg/m3
    Modulus of elasticity
    15 MPa
    Specific heat
    1,45 kJ/(kg*°С)
    Tensile strength at static bending
    0,25 MPa
    Operating temperature range
    -70...+75 °C
    Thickness
    50 mm
    Width
    585 mm
    Lenght
    1185 mm

    PENOPLEX FOUNDATION

    Heat-insulating boards made of extruded polystyrene foam. Used in private housing in loaded structures (eg, foundations, floors, plinths, garden paths).

    more
    thumbnail PENOPLEX FOUNDATION manufactured by extrusion from General purpose polystyrene. Used in private housing in loaded structures (eg, foundations, floors, plinths, garden paths). Plates of this type are characterized by high strength and are able to withstand significant loads during the entire service life (more than 50 years).

    Advantages PENOPLEX:
    • low thermal conductivity;
    • zero water absorption;
    • ecological compatibility;
    • durability;
    • biostability;
    • high compressive and bending strength.

    Aapplication:
    • foundations;
    • floors;
    • plinths;
    • garden paths.

    Technical parameters

    Compressive strength at 10% linear deformation
    0,3 MPa
    Water absorption in 24 hours, not more than % by volume
    0,4
    Water absorption in 28 days % by volume
    0,5
    Fire resistance category
    Г4
    Calculated coefficient of thermal conductivity under operating conditions” B ”
    0,034 W/mK
    Coefficient of vapor permeability
    0,005 mg/(m. h. Pa)
    Density
    27-35 кг/м3
    Modulus of elasticity
    17 MPa
    Specific heat
    1,45 kJ/(kg*°С)
    Tensile strength at static bending
    0,4 MPa
    Operating temperature range
    -70...+75 °C
    Thickness
    50-100 mm
    Width
    585 mm
    Lenght
    1185 mm

    PENOPLEX COMFORT

    Heat-insulating boards made of extruded polystyrene foam. Used for insulation of country houses or city apartments (insulation of walls, balconies, loggias).

    more
    thumbnail PENOPLEX COMFORT manufactured by extrusion from General purpose polystyrene. Used for insulation of country houses or city apartments (insulation of walls, balconies, loggias). L-shaped edge plates allows you to dock them perfectly straight and provide a continuous layer of insulation, which considerably reduces the thickness of the insulation compared to traditional materials.

    Advantages PENOPLEX:
    • low thermal conductivity;
    • zero water absorption;
    • ecological compatibility;
    • durability;
    • biostability;
    • high compressive and bending strength.

    Aapplication:
    • walls;
    • balconies;
    • loggias.

    Technical parameters

    Compressive strength at 10% linear deformation
    0,12 MPa
    Water absorption in 24 hours, not more than % by volume
    0,4
    Water absorption in 28 days % by volume
    0,5
    Fire resistance category
    Г4
    Calculated coefficient of thermal conductivity under operating conditions” B ”
    0,034 W/mK
    Coefficient of vapor permeability
    0,005 mg/(m. h. Pa)
    Density
    от 20 kg/m3
    Modulus of elasticity
    15 MPa
    Specific heat
    1,45 kJ/(kg*°С)
    Tensile strength at static bending
    0,25 MPa
    Operating temperature range
    -70...+75 °C
    Thickness
    20-100 mm
    Width
    585 mm
    Lenght
    1185 mm

    PENOPLEX FASSADE

    Heat-insulating boards made of extruded polystyrene foam. Used for insulation of external and internal enclosing structures (insulation of walls, partitions, facade systems).

    more
    thumbnail PENOPLEX FASSADE manufactured by extrusion from General purpose polystyrene. Used for insulation of external and internal enclosing structures (insulation of walls, partitions, facade systems). The plates have a milled surface, which improves the adhesion of plaster and adhesive compounds to the surface of the material and reduces the time of plastering.

    Advantages PENOPLEX:
    • low thermal conductivity;
    • zero water absorption;
    • ecological compatibility;
    • durability;
    • biostability;
    • high compressive and bending strength.

    Aapplication:
    • walls;
    • partitions;
    • facade systems.

    Technical parameters

    Compressive strength at 10% linear deformation
    0,2 MPa
    Water absorption in 24 hours, not more than % by volume
    0,4
    Water absorption in 28 days % by volume
    0,5
    Fire resistance category
    Г3
    Calculated coefficient of thermal conductivity under operating conditions” B ”
    0,034 W/mK
    Coefficient of vapor permeability
    0,005 mg/(m. h. Pa)
    Density
    25-33 kg/m3
    Modulus of elasticity
    15 MPa
    Specific heat
    1,45 kJ/(kg*°С)
    Tensile strength at static bending
    0,25 MPa
    Operating temperature range
    -70...+75 °C
    Thickness
    20-150 mm
    Width
    585 mm
    Lenght
    1185 mm

    PENOPLEX 45

    Heat-insulating boards made of extruded polystyrene foam. Designed for use in industrial and civil construction, it is a high-strength material for use in any structures where special requirements for loads on the structure.

    more
    thumbnail PENOPLEX 45 manufactured by extrusion from General purpose polystyrene. Designed for use in industrial and civil construction, it is a high-strength material for use in any structures where special requirements for loads on the structure. Material PENOPLEX 45 is actively used in road construction.

    Advantages PENOPLEX:
    • low thermal conductivity;
    • zero water absorption;
    • ecological compatibility;
    • durability;
    • biostability;
    • high compressive and bending strength.

    Aapplication:
    • road construction;
    • aerodrome;
    • Loaded structures.

    Technical parameters

    Compressive strength at 10% linear deformation
    0,6 mPa
    Water absorption in 24 hours, not more than % by volume
    0,2
    Water absorption in 28 days % by volume
    0,4
    Fire resistance category
    Г4
    Calculated coefficient of thermal conductivity under operating conditions” B ”
    0,034 W/mK
    Coefficient of vapor permeability
    0,005 mg/(m. h. PA)
    Density
    38-47 kg/m3
    Modulus of elasticity
    20 mPa
    Specific heat
    1,45 kJ/(kg*°С)
    Tensile strength at static bending
    0,35-0,7 MPa
    Operating temperature range
    -70...+75 °C
    Thickness
    40-100 mm
    Width
    600 mm
    Lenght
    2400 mm

    PAROC FPS 17

    Fire protection slab PAROC FPS 17 is non-combustible stone wool insulation for use as fire protection for steel structures, chimneys, doors, furnaces and ovens.

    more
    thumbnail Fire protection slab PAROC FPS 17 is non-combustible stone wool insulation for use as fire protection for steel structures, chimneys, doors, furnaces and ovens.

    Stone wool insulation has varying fire protection abilities that are largely dependant on the density of the material as well as the used insulation thickness. Generally speaking, the higher the density, the longer the fire protection time.

    PAROC FPS 17 has a density of ~170 kg/m3. The right product for the application will be chosen based on the system provider's approval. PAROC FPS 17 has ETA approval for fire protection for steel structures. The product is easy to handle and install for different kinds of fire applications.

    PAROC stone wool products are capable of withstanding high temperatures. The binder starts to evaporate when its temperature exceeds approximately 200 °C. The insulating properties remain unchanged, but the compressive stress weakens. The softening temperature of stone wool products is over 1000 °C.

    Technical parameters

    Nominal Density
    170 kg/m3
    Width
    600 mm
    Length
    1200 mm
    Thickness
    20-120 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Thermal Conductivity λD
    0,038 W/mK

    PAROC FPS 14

    Fire protection slab PAROC FPS 14 is non-combustible stone wool insulation for use as fire protection for steel structures, chimneys, doors, furnaces and ovens.

    more
    thumbnail Fire protection slab PAROC FPS 14 is non-combustible stone wool insulation for use as fire protection for steel structures, chimneys, doors, furnaces and ovens.

    Stone wool insulation has varying fire protection abilities that are largely dependant on the density of the material as well as the used insulation thickness. Generally speaking, the higher the density, the longer the fire protection time.

    PAROC FPS 14 has a density of ~140 kg/m3. The right product for the application will be chosen based on the system provider's approval. The product is easy to handle and install for different kinds of fire applications.

    Technical parameters

    Nominal Density
    140 kg/m³
    Width
    600 mm
    Length
    1200 mm
    Thickness
    20-120 mm
    Reaction to Fire, Euroclass
    A1
    Thermal Conductivity λD
    0,037 W/mK
    Combustibility
    Non-combustible

    Paroc ROS 30

    Roof slab PAROC ROS 30 is non-combustible stone wool insulation for use as a load bearing thermal insulation layer of existing and new flat roofs.

    more
    thumbnail Roof slab PAROC ROS 30 is non-combustible stone wool insulation for use as a load bearing thermal insulation layer of existing and new flat roofs.

    The roof insulation slab is developed to provide sustainable, hard and fire safe bedding for rigid top insulation layers as well as insulating the bearing layer in renovation sites. The suitable roof slab for flat roof will be chosen based on the product's mechanical properties and thermal conductivity.

    The compressive stress of PAROC ROS 30 is 30 kPa, which means that the slab can carry a 3000 kg/m2 load during installation and use. This means that it is suitable for normal level loads.

    Roof slab PAROC ROS 30g has ventilation grooves in the surface of the board. These grooves enable the constant drying of the whole roof construction.

    Technical parameters

    Width x Length
    1200*1800 mm
    Thickness
    40-250 mm
    Compressive Stress at 10 % deformation CS(10), σ10
    30 kPa
    Reaction to Fire, Euroclass
    A1
    Thermal Conductivity λD
    0,036 W/mK
    Combustibility
    Non-combustible
    Point Load PL(5)
    250 N

    Paroc ROS 40

    Roof slab PAROC ROS 40 is non-combustible stone wool insulation for use as a load bearing thermal insulation layer of existing and new flat roofs.

    more
    thumbnail Roof slab PAROC ROS 40 is non-combustible stone wool insulation for use as a load bearing thermal insulation layer of existing and new flat roofs.

    The roof insulation slab is developed to provide sustainable, hard and fire safe bedding for rigid top insulation layers as well as insulating the bearing layer in renovation sites. The suitable roof slab for flat roof will be chosen based on the product's mechanical properties and thermal conductivity.

    The compressive stress of PAROC ROS 40 is 40 kPa, which means that the slab can carry a 4000 kg/m2 load during installation and use. This means that it is suitable for normal level loads.

    Roof slab PAROC ROS 40g is equipped with ventilation grooves on the upper side. These grooves enable the constant drying of the whole roof construction.

    Technical parameters

    Width x Length
    1200*1800 mm
    Thickness
    40-180 mm
    Compressive Stress at 10 % deformation CS(10), σ10
    40 kPa
    Reaction to Fire, Euroclass
    A1
    Thermal Conductivity λD
    0,037 W/mK
    Water Vapour Transmission MU, µ
    1
    Point Load PL(5)
    350 N
    Combustibility
    Non-combustible

    PAROC ROS 50

    Roof slab PAROC ROS 50 is non-combustible stone wool insulation for use as a load bearing thermal insulation layer of existing and new flat roofs.

    more
    thumbnail Roof slab PAROC ROS 50 is non-combustible stone wool insulation for use as a load bearing thermal insulation layer of existing and new flat roofs.

    The roof insulation slab is developed to provide sustainable, hard and fire safe bedding for most types of flat roof coverings as well as insulating the bearing layer in renovation sites.

    PAROC ROS 50 insulation is used in concrete and corrugated steel constructions as a single-layer insulation. The thickness of the insulation layer should be below 150 mm.

    The compressive stress of the product is 50 kPa, which means that the slab can carry a 5000 kg/m2 load during installation and use.

    Technical parameters

    Width x Length
    1200*1800 mm
    Thickness
    40-100 mm
    Compressive Stress at 10 % deformation CS(10), σ10
    50 kPa
    Reaction to Fire, Euroclass
    A1
    Thermal Conductivity λD
    0,038 W/mK
    Water Vapour Transmission MU, µ
    1
    Point Load PL(5)
    450 N
    Combustibility
    Non-combustible

    PAROC ROS 60

    Roof slab PAROC ROS 60 is non-combustible stone wool insulation for use as a load bearing thermal insulation layer of existing and new flat roofs.

    more
    thumbnail Roof slab PAROC ROS 60 is non-combustible stone wool insulation for use as a load bearing thermal insulation layer of existing and new flat roofs.

    The roof insulation slab is developed to provide sustainable, hard and fire safe bedding for most types of flat roof coverings as well as insulating the bearing layer in renovation sites.

    PAROC ROS 60 insulation is used in concrete and corrugated steel constructions as a single-layer insulation. The thickness of the insulation layer should be below 120 mm.

    The compressive stress of the product is 60 kPa, which means that the slab can carry a 6000 kg/m2 load during installation and use. This means that it is suitable for high level loads.

    Technical parameters

    Width x Length
    1200*1800 mm
    Thickness
    40-130 mm
    Compressive Stress at 10 % deformation CS(10), σ10
    60 kPa
    Tensile Strength Perpendicular to Faces TR, σmt
    10 kPa
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Thermal Conductivity λD
    0,039 W/mK
    Point Load PL(5)
    550 N

    PAROC ROB 60

    Roof board PAROC ROB 60 is non-combustible stone wool insulation for use as a top layer of existing and new flat roofs.

    more
    thumbnail Roof board PAROC ROB 60 is non-combustible stone wool insulation for use as a top layer of existing and new flat roofs.

    The roof insulation board is developed to provide sustainable, hard and fire safe bedding for most types of flat roof coverings as well as insulating the bearing layer in renovation sites.

    The compressive stress of the product is 60 kPa, which means that the slab can carry a 6000 kg/m2 load during installation and use.

    Technical parameters

    Width x Length
    1200*1800 mm
    Thickness
    20-30 mm
    Compressive Stress at 10 % deformation CS(10), σ10
    60 kPa
    Tensile Strength Perpendicular to Faces TR, σmt
    10 kPa
    Reaction to Fire, Euroclass
    A1
    Thermal Conductivity λD
    0,038 W/mK
    Point Load PL(5)
    550 N
    Combustibility
    Non-combustible
    Air Permeability Coefficient, ℓ
    15 x 10-6 m3/m²sPa
    Water Vapour Transmission MU, µ
    1

    PAROC ROB 80

    Roof board PAROC ROB 80 is non-combustible stone wool insulation for use as a top layer of existing and new flat roofs.

    more
    thumbnail Roof board PAROC ROB 80 - is non-combustible stone wool insulation for use as a top layer of existing and new flat roofs.

    The roof insulation board is developed to provide sustainable, hard and fire safe bedding for most types of flat roof coverings as well as insulating the bearing layer in renovation sites.

    The compressive stress of the product is 80kPa, which means that the slab can carry a 8000kg/m2 load during installation and use.

    PAROC ROB 80t - The roof board is faced with natural coloured glass fibre tissue.

    Technical parameters

    Width x Length
    1200*1800 (600*1200) mm
    Thickness
    20-30 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Compressive Stress at 10 % deformation CS(10), σ10
    80 kPa
    Tensile Strength Perpendicular to Faces TR, σmt
    10 kPa
    Thermal Conductivity λD
    0,038 W/mK
    Point Load PL(5)
    700 N
    Water Vapour Transmission MU, µ
    1

    PAROC WAB 10t

    Wall board PAROC WAB 10t is non-combustible stone wool insulation for existing and new ventilated external walls.

    more
    thumbnail Wall board PAROC WAB 10t is non-combustible stone wool insulation for existing and new ventilated external walls.

    The thin wall insulation board can be used as an external layer of two layer-systems in combination with another thermal insulation layer. With a two-layer system you can create a continuous thermal insulation layer with staggered joints to improve the thermal performance of the wall.

    The wall board is faced with natural coloured glass fibre tissue.

    Technical parameters

    Width x Length
    2400*1200 mm
    Thickness
    20 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Thermal Conductivity λD
    0,036 W/mK
    Air Permeability Coefficient, ℓ
    10 x 10-6 m2/Pa*s
    Facing Material
    Glass fibre tissue
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²

    PAROC WAS 25

    Wall slab PAROC WAS 25 is non-combustible stone wool insulation for existing and new ventilated external walls.

    more
    thumbnail Wall slab PAROC WAS 25 is non-combustible stone wool insulation for existing and new ventilated external walls.

    The wall insulation slab is used as an external layer of two layer-systems in combination with another low-density thermal insulation layer. With a two-layer system it is easy to create a continuous thermal insulation layer with staggered joints to improve the thermal performance of the wall.

    PAROC WAS 25t - The wall slab is faced with natural coloured glass fibre tissue.

    Technical parameters

    Width x Length
    600*1200 mm
    Thickness
    30-120 mm
    Air Permeability Coefficient, ℓ
    25 x 10-6 m2/Pa*s
    Thermal Conductivity λD
    0,033 W/mK
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²
    Water Vapour Transmission MU, µ
    1

    PAROC WAS 35

    Wall slab PAROC WAS 35 is non-combustible stone wool insulation for existing and new ventilated external walls.

    more
    thumbnail Wall slab PAROC WAS 35 is non-combustible stone wool insulation for existing and new ventilated external walls.

    The wall slab insulation can be used in one layer-systems where the insulation and the surface layer against the ventilation cavity is taken care of by a single product.

    PAROC WAS 35t - The wall slab is faced with natural coloured glass fibre tissue.

    Technical parameters

    Width x Length
    600*1200 mm
    Thickness
    30-150 mm
    Air Permeability Coefficient, ℓ
    35 x 10-6 m2/Pa*s
    Thermal Conductivity λD
    0,033 W/mK
    Reaction to Fire, Euroclass
    A1
    Water Vapour Transmission MU, µ
    1
    Combustibility
    Non-combustible
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²

    PAROC WAS 50

    Wall slab PAROC WAS 50t is non-combustible stone wool insulation for existing and new slightly ventilated external walls.

    more
    thumbnail Wall slab PAROC WAS 50 is non-combustible stone wool insulation for existing and new slightly ventilated external walls.

    The product is suitable for the insulation of walls with brick facades. The wall slab insulation can be used in one layer-systems where the insulation and surface layer against the ventilation cavity is taken care of by a single product.

    PAROC WAS 50t - The wall slab is faced with natural coloured glass fibre tissue.

    Technical parameters

    Width x Length
    600*1200 mm
    Thickness
    50-150 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Thermal Conductivity λD
    0,034 W/mK
    Air Permeability Coefficient, ℓ
    50 x 10-6 m2/Pa*s
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²

    PAROC Fatio

    Rendered facade slab PAROC Fatio is non-combustible stone wool insulation for use as a base layer of both thin and thick rendering facade in existing and new buildings.

    more
    thumbnail Rendered facade slab PAROC Fatio is non-combustible stone wool insulation for use as a base layer of both thin and thick rendering facade in existing and new buildings.

    The rendered facade insulation slab has excellent thermal insulation and alkali resistance properties. It doesn't accumulate moisture or react to changes in temperature.

    With the rendered facade insulation slab you can easily create a smooth base layer for thick rendering in case of an uneven surface of the supporting wall. At the same time, you will improve the sound insulation and increase the fire resistance of the external wall.

    Technical parameters

    Length
    1200 mm
    Width
    600 mm
    Thickness
    50-150 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Tensile Strength Perpendicular to Faces TR, σmt
    5 kPa
    Compressive Stress at 10 % deformation CS(10), σ10
    10 kPa
    Thermal Conductivity λD
    0,035 W/mK
    Water Vapour Transmission MU, µ
    1,0

    PAROC Linio 10

    Rendered facade slab PAROC Linio 10 is non-combustible stone wool insulation for use as a base layer for thin rendering facade in existing and new buildings.

    more
    thumbnail Rendered facade slab PAROC Linio 10 is non-combustible stone wool insulation for use as a base layer for thin rendering facade in existing and new buildings.

    The rendered facade insulation slab has excellent thermal insulation and mechanical properties. It doesn't accumulate moisture or react to changes in temperature.

    With the rendered facade insulation slab you can easily create a smooth base layer for thin and thick rendering in case of an uneven surface of the supporting wall. At the same time, you will improve the sound insulation and increase the fire resistance of the external walls.

    Advantages
    • Slab insulation is suitable for insulation of all types of walls.
    • This type of insulation is particularly recommended when the surface of the supporting wall structure is uneven.
    • The insulation slabs are fastened to the supporting wall structure by gluing and using mechanical fasteners.

    Technical parameters

    Length
    1200 mm
    Width
    600 mm
    Thickness
    40-200 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Tensile Strength Perpendicular to Faces TR, σmt
    10 kPa
    Compressive Stress at 10 % deformation CS(10), σ10
    20 kPa
    Thermal Conductivity λD
    0,036 W/mK
    Water Vapour Transmission MU, µ
    1,0

    PAROC Linio 15

    Rendered facade board PAROC Linio 15 is non-combustible stone wool insulation for use as a base layer of thin rendered facade around the openings of existing and new buildings.

    more
    thumbnail Rendered facade board PAROC Linio 15 is non-combustible stone wool insulation for use as a base layer of thin rendered facade around the openings of existing and new buildings.

    PAROC Linio 15 board has excellent thermal insulation and alkali resistance properties. It doesn't accumulate moisture or react to changes in temperature.

    With thin rendered facade insulation board you can easily create a smooth base layer for thin rendering around windows and doors where the thickness of the layer is critical.

    Advantages
    • Slab insulation is suitable for insulation of all types of walls.
    • This type of insulation is particularly recommended when the surface of the supporting wall structure is uneven.
    • The insulation slabs are fastened to the supporting wall structure by gluing and using mechanical fasteners.

    Technical parameters

    Length
    1200 mm
    Width
    600 mm
    Thickness
    20-200 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Tensile Strength Perpendicular to Faces TR, σmt
    15 kPa
    Compressive Stress at 10 % deformation CS(10), σ10
    30 kPa
    Thermal Conductivity λD
    0,037 W/mK
    Water Vapour Transmission MU, µ
    1,0

    PAROC Linio 80

    Rendered facade lamella PAROC Linio 80 is non-combustible stone wool insulation for use as a base layer of thin rendered facade in existing and new buildings.

    more
    thumbnail Rendered facade lamella PAROC Linio 80 is non-combustible stone wool insulation for use as a base layer of thin rendered facade in existing and new buildings.

    The lamella has excellent thermal insulation and alkali resistance properties. It doesn't accumulate moisture or react to changes in temperature.

    With rendered facade insulation lamella you can easily create a smooth base layer for thin rendering, improve the sound insulation and increase the fire resistance of walls. Lamellas are installed with adhesive mortar. Separate mechanical fasteners are not normally needed (check the system owner instructions).
    Advantages
    • It is fast and easy to install.
    • It normally requires no mechanical fasteners. The lamellas are glued to the supporting wall using adhesive mortar.
    • It provides an even basis for the rendering because the surface of the lamella is sawn.
    • The lamellas have very high tensile strength, which makes them suitable for situations where high mechanical strength is required.

    Technical parameters

    Length
    1200 mm
    Width
    200 mm
    Thickness
    50-220 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Thermal Conductivity λD
    0,040 W/mK
    Tensile Strength Perpendicular to Faces TR, σmt
    80 kPa
    Compressive Strength CS(Y), σm
    50 kPa
    Water Vapour Transmission MU, µ
    1,0
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²

    PAROC eXtra

    General insulation slab PAROC eXtra is made of non-combustible stone wool and used for thermal, sound and fire insulation applications, such as walls, attics and floors, in all kinds of buildings.

    more
    thumbnail General insulation slab PAROC eXtra is made of non-combustible stone wool and used for thermal, sound and fire insulation applications, such as walls, attics and floors, in all kinds of buildings.

    The highly insulating general insulation slab is soft and rigid. The slab is easy to handle, cut and install for different kinds of applications. The insulation doesn't settle, shrink or loose its insulation properties during its lifetime.

    The greater density of the slab is not prone to convection so the thermal resistance of the product is maintained even during extremely cold winters.

    Technical parameters

    Length
    1200 mm
    Width
    600 mm
    Thickness
    50-200 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Thermal Conductivity in 10 °C, λ10
    0,036 W/mK
    Thermal Conductivity in 25 °C, λ25
    0,038 W/mK
    Air Permeability Coefficient, ℓ
    100 x 10-6 m2/Pa*s
    Water Vapour Transmission MU, µ
    1,0

    PAROC eXtra plus

    General insulation slab PAROC eXtra plus is made of non-combustible stone wool and used for thermal, sound and fire insulation applications, such as walls, attics and floors, in all kinds of buildings.

    more
    thumbnail General insulation slab PAROC eXtra plus is made of non-combustible stone wool and used for thermal, sound and fire insulation applications, such as walls, attics and floors, in all kinds of buildings.

    Soft and rigid PAROC eXtra plus has very low thermal conductivity so it is used in applications where construction depth is critical.

    The slab is easy to handle, cut and install for different kinds of applications. The insulation doesn't settle, shrink or loose its insulation properties during its lifetime.

    The greater density of the slab is not prone to convection so the thermal resistance of the product is maintained even during extremely cold winters.

    Technical parameters

    Length
    1200 mm
    Width
    600 mm
    Thickness
    50-150 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Thermal Conductivity in 10 °C, λ10
    0,034 W/mK
    Thermal Conductivity in 25 °C, λ25
    0,036 W/mK
    Air Permeability Coefficient, ℓ
    60 x 10-6 m2/Pa*s
    Water Vapour Transmission MU, µ
    1,0
    Модуль кислотности
    2,2
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²

    PAROC SSB 1

    Step sound board PAROC SSB 1 is non-combustible stone wool insulation for use as a sound absorbing layer (spring) for the reduction of impact sound in floating floors.

    more
    thumbnail Step sound board PAROC SSB 1 is non-combustible stone wool insulation for use as a sound absorbing layer (spring) for the reduction of impact sound in floating floors.

    The fibre orientation in the step sound insulation slab is mainly horizontal compared to, for example, a roof slab or ground slab. The horizontal fibre direction gives a lower dynamic stiffness, which means better impact sound insulation.

    The compressive stress of the product is 10 kPa, which means that it can carry a 1000 kg load during installation and use.

    Technical parameters

    Length
    1200 mm
    Width
    600 mm
    Thickness
    20-50 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Compressive Stress at 10 % deformation CS(10), σ10
    15 kPa
    Thermal Conductivity λD
    0,035 W/mK
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²
    Water Vapour Transmission MU, µ
    1

    PAROC SSB 4

    Step sound board PAROC SSB 4 is non-combustible stone wool insulation for use as a sound absorbing layer (spring) for the reduction of impact sound in floating floors.

    more
    thumbnail Step sound board PAROC SSB 4 is non-combustible stone wool insulation for use as a sound absorbing layer (spring) for the reduction of impact sound in floating floors.

    The fibre orientation in the step sound insulation slab is mainly horizontal compared to, for example, a roof slab or ground slab. The horizontal fibre direction gives a lower dynamic stiffness, which means better impact sound insulation.

    The compressive stress of the product is 40 kPa, which means that the slab can carry a 4000 kg/m2 load during installation and use. PAROC SSB 4 can be used both in concrete and timber structures.

    Technical parameters

    Length
    1200 mm
    Width
    600 mm
    Thickness
    50-100 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Compressive Stress at 10 % deformation CS(10), σ10
    40 kPa
    Thermal Conductivity λD
    0,037 W/mK
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²

    PAROC GRS 20

    Ground slab PAROC GRS 20 is non-combustible stone wool insulation for existing and new basement walls and ground floors.

    more
    thumbnail Ground slab PAROC GRS 20 is non-combustible stone wool insulation for existing and new basement walls and ground floors.

    The water repellent ground insulation slab can be used as thermal insulation and capillary break both in the external layer of a foundation and underground slab.

    The compressive stress of the slab is 20 kPa, which means that the slab can carry a 2000 kg/m2 load. To work correctly, the other side of the external ground insulation has to be against a warm construction such as a wall of floor.

    Technical parameters

    Width
    1200 mm
    Length
    600 mm
    Thickness
    50-100 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Compressive Stress at 10 % deformation CS(10), σ10
    20 kPa
    Thermal Conductivity λD
    0,035 W/mK
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²
    Water Vapour Transmission MU, µ
    1

    PAROC CGL 20

    Ceiling lamella is non-combustible stone wool insulation for existing and new cellar ceilings.

    more
    thumbnail Ceiling lamella PAROC CGL 20 is non-combustible stone wool insulation for existing and new cellar ceilings. With ceiling insulation lamella you can easily insulate cellar ceilings, creating good sound absorption for the space and increasing fire safety between floors.

    PAROC CGL 20cy - Glued lamella insulation with faceted edges forms a structured base layer for the ceiling surface. The visible surface of the lamella is pre-painted/coated for better application of the paint.

    PAROC CGL 20cyc - Glued lamella insulation with faceted edges forms a structured base layer for the ceiling surface. The lamella is pre-painted/coated on both sides.

    PAROC stone wool products are capable of withstanding high temperatures. The binder starts to evaporate when its temperature exceeds approximately 200°C. The insulating properties remain unchanged, but the compressive stress weakens. The softening temperature of stone wool products is over 1000°C.

    Technical parameters

    Length
    1200 mm
    Width
    200 mm
    Thickness
    50-200 mm
    Reaction to Fire, Euroclass
    A1
    Combustibility
    Non-combustible
    Compressive Strength CS(Y), σm
    20 kPa
    Thermal Conductivity λD
    0,037 W/mK
    Air Flow Resistivity AFR
    10 kPa*s/m²
    Water Absorption, Short Term WS, Wp
    ≤ 1 kg/m²
    Water Absorption, Long Term WL(P), Wlp
    ≤ 3 kg/m²




      8 (800) 707-53-99 Звонок по России бесплатный
      firm@sevren.ru